How to apply wind loads on the building

Betonarme tasarım hakkında sorular, görüşler, öneriler

How to apply wind loads on the building

Mesajgönderen ammer » 09 Eyl 2019, 11:07

hello friends
How to apply wind loads on the building?
regards :D :D :D
ammer
 
Mesajlar: 404
Kayıt: 11 Eki 2011, 10:32
Konum: Iraq

Re: How to apply wind loads on the building?

Mesajgönderen ammer » 09 Eyl 2019, 12:19

i have calculated the wind pressure by using UBC 97 and it was equal to 0.50 kn\m2
how to calculate the wind pressures for each floors using IDECAD ?
Eklentiler
2019-09-09_105829.jpg
2019-09-09_105829.jpg (347.47 KiB) 304 kere görüntülendi
ammer
 
Mesajlar: 404
Kayıt: 11 Eki 2011, 10:32
Konum: Iraq

Re: How to apply wind loads on the building?

Mesajgönderen ammer » 09 Eyl 2019, 15:28

And how it will applying on the building
Please show them at the image
ammer
 
Mesajlar: 404
Kayıt: 11 Eki 2011, 10:32
Konum: Iraq

Re: How to apply wind loads on the building?

Mesajgönderen ammer » 10 Eyl 2019, 10:36

HELLO FRIENDS
NEED HELP :( :(
ammer
 
Mesajlar: 404
Kayıt: 11 Eki 2011, 10:32
Konum: Iraq

Re: How to apply wind loads on the building?

Mesajgönderen nurgulkaya » 10 Eyl 2019, 13:24

Hello,

If your floor height is the same on all floors, you must multiply by calculating the façade areas for the 0.5 and x and y directions. Then divide the force you find by the number of stories. Enter the value you find in the wind section in the analysis settings tab.

But we have problem with TBDY 2018 and wind analysis. We recommend that you analyze the model in version 8.62.
Kullanıcı avatarı
nurgulkaya
 
Mesajlar: 611
Kayıt: 02 Mar 2014, 18:28
Konum:

Re: How to apply wind loads on the building?

Mesajgönderen ammer » 10 Eyl 2019, 14:11

HELLO nurgulkaya
many thanks to your efforts
as the below image which are showed the windward pressure
do the idecad considering the Leeward pressure?
Eklentiler
2019-09-09_105829.jpg
2019-09-09_105829.jpg (388.22 KiB) 207 kere görüntülendi
ammer
 
Mesajlar: 404
Kayıt: 11 Eki 2011, 10:32
Konum: Iraq

Re: How to apply wind loads on the building

Mesajgönderen ammer » 11 Eyl 2019, 10:06

hello friend
I'm waiting your answer please
:D :D :D
ammer
 
Mesajlar: 404
Kayıt: 11 Eki 2011, 10:32
Konum: Iraq

Re: How to apply wind loads on the building

Mesajgönderen HakanŞahin » 11 Eyl 2019, 12:17

Hi Ammer,

Wind loads(W) can be acted as "total lateral forces" to rigid diaphrams for each stories on x and y directions of structure. If your 0.50 kn/m2 is total wind load of windward+ leeward pressure for your project.

Wind load for 4 metres story on x direction= 17 * 0.5 * 4 =34 KN
Wind load for 3.5 metres story on x direction= 17 * 0.5 * 3.5 = 29.75 KN

Wind load for 4 metres story on y direction= 45* 0.5 * 4 =90 KN
Wind load for 3.5 metres story on y direction= 45 * 0.5 * 3.5 =78.75 KN

You need to input these values as positive values on each story.

ideCAD considers windload results as combanations, which are:
G+ 1.3Q + 1.3W
G+ 1.3Q - 1.3W
0.9G + 1.3W
0.9G - 1.3W
2.PNG
2.PNG (16.22 KiB) 150 kere görüntülendi


Combanations are created according to TS500

you may see windload results in any element's reinforments dialog.
1.PNG
1.PNG (80.75 KiB) 148 kere görüntülendi
Kullanıcı avatarı
HakanŞahin
Site Admin
 
Mesajlar: 2922
Kayıt: 09 Eki 2008, 10:37
Konum:

Re: How to apply wind loads on the building

Mesajgönderen ammer » 11 Eyl 2019, 12:44

hello mr. hakan we missed you
thanks to your efforts :D :D
it's was very useful
by regards
ammer
 
Mesajlar: 404
Kayıt: 11 Eki 2011, 10:32
Konum: Iraq


Dön ideCAD ile Betonarme Tasarım

Kimler çevrimiçi

Bu forumu gezen kullanıcılar: Google [Bot] ve 9 misafir